Silt Fence Plow
Push Pull Silt Fence Plow Attachment
- Dedicated quick attach skid loader mounting
- Installs silt fence either going forward with a skid loader or backwards
- Offsets 51" from the center of the plow when going forward
- Can offset in the pull position 24" or 42" from the center of the plow in the pull position
- 36" fabric chute installs 36" and shorter fabric
- 48" fabric chute installs 48" and smaller fabric
- 1" Thick mole board knife
- Replaceable 2" wide hardened self sharpening cutting tip
- Spring loaded hardened 16" diam. cutting coulter to cut through soil, trash, tree roots
- Grade 8 5/8" x 4" shear bolt protection
- Forklift / hoist slots for easy moving
- Rear Pivot has a 90 degree swing to either side of center for tight turning
- Massive 2" x 8" greasable pivot pins
- Simple swing dampening brake with adjustable tension setting to keep the rear pivot from slapping when in transport position - no springs to wear out or break
- 6" x 4" x 3/8" structural steel main beam construction
- Up to 1500' rolls of silt fence material can be used
- fabric tension spring with 16" diameter fabric plate
- Can install silt fence 6" to 20" deep. The depth needed to install silt fence material is determined by the specs of the job and soil conditions. Most contractors install silt fence 8" - 10" deep.
- Retractable storage legs with pads fro stability
- 36" Push Pull model weight 995 #s and 48" model weighs 1121 #s
Features
Specifications
PP-SFP36
| Height Knife Setting Top: Bottom: |
76”
71” |
|---|---|
| Width |
60”
|
| Length |
120”
|
| Weight |
1,090 lbs.
|
| Offsetting Ability In pull positions from center |
29” and 40” from center
|
| Offset in push position from center |
51”
|
PP-SFP42
| Height Knife Setting Top: Bottom: |
76”
71” |
|---|---|
| Width |
60”
|
| Length |
131”
|
| Weight |
1,105 lbs.
|
| Offsetting Ability In pull positions from center |
29” and 40” from center
|
| Offset in push position from center |
51”
|
PP-SFP48
| Height Knife Setting Top: Bottom: |
76”
71” |
|---|---|
| Width |
60”
|
| Length |
137”
|
| Weight |
1,165 lbs.
|
| Offsetting Ability In pull positions from center |
29” and 40” from center
|
| Offset in push position from center |
51”
|
Accessories and Attachments
TSA-1051 – Three Point Hitch to Skid loader Adapter Bracket
The TSA-1051 Three Point to Skid loader Adapter Bracket allows a dedicated skid loader mounted machine to be operated off the three point hitch of a tractor. It has Cat I and II three point hitch mountings. A hyd. top link is required when using the TSA-1051 mounting on Silt Fence Plows and is recommended when using it on any other skid loader attachment.
RWU-1056 Wire Unroller
The wire unroller mounts on either side of the machine. It allows a roll of wire to be unrolled as the fabric is being sliced into the ground. It will not install the wire into the ground. If you need to install the wire and the fabric into the ground together look at the Enfencer machine on our website. With the Push Pull model the wire unroller can only be used in the backwards position.
FC-1136 - 36" & FC-1148 - 48" Fabric Curtains
The fabric curtain is a plastic divider that separates the fabric so it does not rub against itself when going through the fabric chute. It is only needed when using non woven fabrics to prevent the fabric from grabbing itself and pulling down. With the slick woven fabric, the divider is not needed.
CONTACT US
ADDRESS
36428 US HWY 69N Jacksonville Texas 75766
ADDRESS
17469 US 69, Tyler, Texas 75703
PHONE
903-600-4800
903-586-8999